| 6101 BODY CONSTRUCTION/MATERIALS:
Subsils - .500" x 3.00" full-length flat aluminum body
subsils
Crossmembers - Two (2) 2.00" x 3.00" x 50.00 x .125"
wall tubular aluminum body crossmembers full-welded to above subsils,
one (1) located at front body panel and (1) set 18 from front of body.
Two (2) 2.00 x 3.00 x full body width x .125 wall tubular aluminum
body crossmembers full-welded to above subsils, one (1) located at rear
of front compartment, one (1) set middle of side/rear compartments.
One (1) 2.00" x 3.00" x full body width x .25" wall tubular aluminum
body crossmembers full-welded to above subsills set at rear body panel.
Six (6) 2.00 x 2.00 x .125 wall tubular spacers welded to top of
crossmembers, 22 in length, between body crossmembers and upper/rearward
compartments to provide tire/chain clearance.
Front Body Panel - .188" aluminum 50.00" wide x 34.00"
high front body panel welded at sides to back of side compartment boxes.
Panel to have upper 2.00" x .500" breakover lip between compartments.
Top of panel to remain 2.00" lower than top of body for installation
of following skid unit tank.
Compartments - Four (4) aluminum modular-free standing
full-welded compartment boxes installed - one (1) each 36.00" wide x
49.00" high x 22.00" deep lower/forward forward body area and one (1)
each 70.00" wide x 31.00" high x 22.00" deep upper/rearward body area.
Compartments to be constructed of .125" smooth aluminum with panels
forming front and rear body panels to be constructed of .188" aluminum.
Compartments strip-welded to forward body panel, adjacent compartment
and body crossmembers. Compartments to have full-welded seams and 1-5/8"
x 1-1/2" door opening flange(s). Lower compartment floor flanges
turned downward to create "sweep-out" type compartment floors.
Note - actual door openings less 4 height, 2 width.
Rear Body Wheelhousing/Skirt Panels - .125" aluminum tread/brightplate
lower wheelhousing/rear body skirt panels installed with opening for
rear chassis wheels and chassis fuel fill. Skirt panels extended to
approx. 4" above center-line of rear chassis wheels. Panels extended
from lower/forward compartment to rear body skirt panel and have 2"
lower panel reinforcement lip.
Rear Body Panel - .125" aluminum tread/brightplate 50.00"
wide rear-facing body panel installed in center-line of lower/rear body
skirt area from rear step level to 4" above rear body crossmember.
Top Body Deck Risers - four (4) .750" x 1.00" x full length
x .125" wall tubular aluminum risers installed on top of exterior compartment
boxes to create space under top body decks for installation of wiring.
Top Body Decks - .125" aluminum tread/brightplate upper
body decks installed full-length x full-width of upper deck areas created
by above compartment box ceilings. Decks to have 2.75" front, rear and
side-facing 90-degree lips with corners full welded.
Rubrail Caps - .125" aluminum tread/brightplate 2.00"
wide rubrail caps extended from front body corners to wheelhousing panel
- one each side under forward compartment door opening(s).
Drainage Holes - four (4) .500" dia. drainage holes installed,
one (1) each corner of under skid-unit floor for drainage of skid unit
bed area. 5.00" dia. drain hole installed in under skid-unit floor
at following skid unit tank overflow.
6102. COMPARTMENT DOORS:
Compartment door openings equipped with ROM Robbins roll-up
type shutter doors installed per ROM installation specifications with
following features:
Lift bar with key lock
Satin finish
6103. REAR STEP:
Full width x 8.00" deep open-grate Grip-Strut 12 ga. aluminum
rear step deck installed in .125" x 2" x 1" aluminum framework.
Step reinforced to rear chassis frame rails with 3.00" steel channel
and .125" aluminum tread/brightplate installed on side and rear-facing
step flanges.
6104. BODY MOUNTING:
Sub-Sils - Two (2) .750" x 3.00" pressure-treated oak
frame sils installed - full length between chassis frame rails and body
subsils.
Fuel Fill - OEM fuel fill/spout kit installed with Cast
Products hinged spring-loaded access door installed on body wheelhousing
panel.
U-bolts - Six (6) .625" body mounting U-bolts installed
- three (3) each side
Undercoating - Body skirting areas undercoated with Tectyl
#115F waxed-based undercoating material prior to body mounting. All
tread plate areas coated with neoprene based Silaprene on body-side
surfaces prior to installation.
6105. PAINTING:
Body prepared for prime painting with Sherwin-Williams
DualEtch and prime painted with Sherwin-Williams Jet-Seal non-sanding
primers. Three (3) wet-on-wet coats of Sherwin-Williams Acryld acrylic
enamel with Polysol urethane additive applied - color to match chassis
cab.
6106. 12VDC ELECTRICAL:
Wiring - All body wiring to be 14 ga. color coded stranded
type wiring installed in protective split looms with solderless connectors.
Body electrical equipment to include:
Marker/ICC Lights - all required DOT/ICC marker lights
and reflectors installed
Stop-Tail/Turn/Back-Up Lights - Six (6) Weldon #2030 surface
mounted lights installed on lower rear-facing body skirt panel - two
(2) red (stop/tail), amber (turn) and clear (back up) connected to chassis
circuit(s).
Step/License Lights - Two (2) Arrow #431 chrome framed
surface mounted step/license lights surface mounted on lower rear body
splash pan and connected to chassis tail light circuit.
DOT Flairs - One (1) set triangular DOT reflective flairs
installed.
Back-up Alarm - One (1) Ecco #550 connected to chassis
back-up light system.
6107. 110VAC ELECTRICAL:
See following optional 110VAC specifications.
6108. DELIVERY PREPARATION:
Customer's chassis oil, grease and water levels checked
and filled to recommended levels. Batteries fully charged.
Unit weighed and road tested. All auxiliary equipment serviced
and tested for proper operation.
6109. INSPECTIONS:
SWAB Wagon Company, Inc. encourages periodic inspections
by customer. Inspections shall be scheduled in advanced.
Inspection teams shall be limited to a maximum of six (6) personnel.
6110. CHANGES & ADDITIONS:
All Changes & Additions to contract, including additional
charges or credits, shall be submitted to customer for approval.
All submissions, accepted or rejected, shall be returned to SWAB Wagon
Company, Inc. In the case of an accepted Change & Addition,
the work shall not be implemented until such time as the necessary documents
have been returned to SWAB Wagon Company, Inc. and the conditions (terms),
if any, of the order have been satisfied.
6111. INSURANCE:
Customer's chassis to be insured by chassis-owner against
fire, theft, vandalism, storm damage, etc. while at Swab Wagon Company,
Inc. plant.
6112. WARRANTY:
The following warranty will apply to new All-Aluminum
Rescue Body/Equipment built by Swab Wagon Company, Inc. (hereafter referred
to as SWAB).
Structural Warranty - (10) ten years/ (120) months
from date of delivery to original owner for 100% of expense to perform
required replacement/repairs to correct defects in design, construction,
materials and/or workmanship against cracking and/or perforation caused
by corrosion including:
Body Framing/Crossmembers
Compartment/Body Doors
Exterior/Interior Panels
Treadplate Panels/Trim
Compartment Boxes
Corrosion Warranty - (5) five years (60) months
from date of delivery to original owner for 100% of expense to perform
required replacement/repairs to correct defects in exterior/interior
body finish against corrosion damaged caused by reaction between dissimilar
metals and/or defects in undercoating, caulking and/or painting process.
Electrical/Paint/Trim Warranty - (2) years/ (24)
months from date of delivery to original owner for 100% expense to perform
required replacement/repair to correct defects in design, installation,
and/or workmanship including:
12 Volt Wiring
Generator/Pump Installation(s)
110/220 Volt Wiring
Lighting Installation(s)
Upholstery/Trim
Exterior/Interior Paint
Hardware/Plating/Fasteners
Tread Plate Trim Panels
Windows (Excluding Glazing)
Lettering/Striping
Warranty
Policy/ Procedure(s):
SWAB warrants the above listed body and equipment in accordance
with the above time limits, beginning with delivery of completed body/equipment
to customer. Notification of Warranty Claim must be submitted
within the above warranty period(s). All Warranties voided by
accident repair(s)/body modification(s)/transfer to new chassis by a
party other than SWAB unless approved in writing by SWAB. All
Warranties voided upon transfer of ownership to another party from original
owners.
Upon notification, SWAB will perform required repair/replacement
work under the following procedures. SWAB reserves the right to
stipulate which procedure warranty work will be performed by:
At customers location by Swab service personnel.
At customers location by qualified outside contractor upon receipt
by SWAB of quotation/approval for said work.
At SWAB plant in Elizabethville, PA in which case the unit will
be returned to SWAB at owners expense.
Auxiliary Equipment Items - auxiliary equipment
items not manufactured by SWAB to carry manufacturer replacement/repair
warranty and labor policy including but not limited to:
Pumps
Air Conditioners
Generators
Winches
Warning Devices
Chassis/Equipment
6113. OWNERS MANUAL AND EQUIPMENT WARRANTIES:
All equipment specification, instruction, installation
manuals, and parts schematics placed in booklet form and installed in
completed unit.
6114. RESEARCH AND DEVELOPMENT:
For purposes of product improvement and/or installation of specified optional
equipment, Swab Wagon
Company,
Inc. reserves the right to modify above specifications without notice.
6200. OPTIONAL CHASSIS ITEMS:
6300. OPTIONAL BODY/COMPARTMENT ITEMS:
6400. OPTIONAL 12VDC ELECTRICAL ITEMS:
6500. OPTIONAL 110VAC ELECTRICAL ITEMS:
6600. OPTIONAL WARNING LIGHTS AND SIRENS:
6700. OPTIONAL AUXILIARY EQUIPMENT: None
6800. OPTIONAL LETTERING/STRIPING:
6900. SKID UNIT:
7000. PRICE QUOTATION(S):
7100. TERMS & CONDITIONS:
7200. OPTIONAL PRICE QUOTATION(S):
|
